Difference between revisions of "Enable SSH Without Opening the Apple TV"
m (→Step 4)
|Line 87:||Line 87:|
Revision as of 17:04, 9 May 2007
- External USB drive
- boot.efi from appletv
- licensed copy of os x for intel
- usb hub w/ external power
THE METHOD DESCRIBED BELOW ASSUMES THE USB DRIVE OR IPOD YOU ARE INSTALLING TO IS EMPTY AND HAS NO DATA THAT YOU CARE ABOUT. PLEASE USE CAUTION
Install full Mac OS X onto the device, using semthex's kernel and instructions detailed here: Apple TV Hacks - Mac OS X running on Apple TV. If you're installing to a small device you'll want to read the instructions for a minimal install Here.
Modify the AppleFileSystemDriver, add this text to the file /System/Library/Extensions/AppleFileSystemDriver.kext/Contents/Info.plist in the IOPropertyMatch array section. This can be done easily in the Finder with the TextEdit application.
<dict> <key>Content Hint</key> <string>5265636F-7665-11AA-AA11-00306543ECAC</string> <key>Leaf</key> <true/> </dict> <dict> <key>Content Hint</key> <string>Apple_Recovery</string> <key>Leaf</key> <true/> </dict>
Very special thanks to Turbo for this patch. If you skip this step then OSX won't boot and will complain that it is waiting for the root device
Now we are going to change the partition info to that of a recovery system. This requires the use of the Terminal application. It is imperative that you ensure you are working with the proper disk. If you have only one internal hard disk in your system and the disk you want to modify is your only external disk, then it will likely be identified as /dev/disk1. To make sure, type diskutil list at the command prompt to see all disks attached to your system.
Then, assuming /dev/disk1 is the correct disk, using the command sudo gpt show /dev/disk1 should get results such as these:
start size index contents 0 1 PMBR 1 1 Pri GPT header 2 32 Pri GPT table 34 6 40 409600 1 GPT part - C12A7328-F81F-11D2-BA4B-00A0C93EC93B 409640 116538416 2 GPT part - 48465300-0000-11AA-AA11-00306543ECAC 116948056 262151 117210207 32 Sec GPT table 117210239 1 Sec GPT header
Where index 1 is the EFI partition and index 2 is the Mac OS X installation.
THE FOLLOWING INSTRUCTIONS ASSUME /dev/disk1 IS YOUR EXTERNAL DRIVE. YOU CAN BREAK YOUR SYSTEM IF IT ISN'T.
First unmount the disk. Otherwise you will get a 'Resource busy' error.
disktool -u disk1
Now do this to set up the drive to work as a recovery partition:
gpt remove -i 2 /dev/disk1
Then take the numbers from above and plug them in respectively, for me the start point is 409640 and the size is 116538416
gpt add -b 409640 -i 2 -s 116538416 -t 5265636F-7665-11AA-AA11-00306543ECAC /dev/disk1
Remove the drive from your Mac and connect it to the Apple TV. Use a USB hub so you can also connect a keyboard and mouse. Reboot the Apple TV by pressing and holding the 'menu' and '-' buttons simultaneously on the Apple remote until the reboot occurs.
The ATV OS is on the partition labled 'OSBoot'. Instructions for enabling SSH are located here. I used appletv-install.sh to copy the necessary files (gdb will probably fail, that is ok you can ignore it). Be sure to enable ssh on your Mac OS X install before you run this script so that it copies the ssh.plist file that has sshd enabled and not disabled.
The below is redundant, apparently you can also use mount_hfs to mount your partition, but I have documented success using the below method also - MrZ
If you mess up and want to mount your "repair" partition again, you can just reverse the steps, but change
gpt add -b 409640 -i 2 -s 116538416 -t 5265636F-7665-11AA-AA11-00306543ECAC /dev/disk1 to gpt add -b 409640 -i 2 -s 116538416 -t 48465300-0000-11AA-AA11-00306543ECAC /dev/disk1
The repair partition shows up again on your machine, and you can edit it.